How much does Mold Removal Taylor cost?
- Distinguish the cause of the mold growth
- Decide whether moisture source has been removed
- Determine the type of mold
- What amount of the house or business has mold?
- What sort of materials is contaminated?
- How simple is it to get to the mold?
Best Tips for Mold Removal Taylor
Mold & Moisture
The crawl space is the number one source for potential moisture entering your home. The moisture may be equal to gallons of water but in vapor form and not even visible. A seal tight liner kit will instantly stop the moisture in the crawl space from entering home as well as eliminating radon gas, musty odors, mildew and mold.
"The U.S. EPA states: "Molds are usually not a problem unless mold spores land on a wet or damp spot and begin growing. Molds produce allergens, irritants and potentially toxic substances. The key to mold control is moisture control. The mold will not grow if moisture is not present (source: EPA " A Brief Guide to Mold, Mildew and Your Home," publication #402-K-02-003)."
Eliminate the Existing Mold
To eliminate and prevent future mold growth, spray the affected areas with a mold killing and growth preventing spray, there are good products for purchase at your local building supply house.
My Take on the Problems with Bleach
The Myth Of Using Bleach To Kill Mold! Mold has a root system that actually grows into the surfaces of wood, drywall, concrete, etc..., like tree roots grow into the soil. The roots are not killed by bleach alone because the bleach does not penetrate the surface of porous materials. The bleach chemical portion sits on the surface until gassing off, killing only the mold on the surface leaving the roots intact, while the water portion of the bleach soaks into the material giving the mold roots a food source to start growing again. Think of it this way, if you were to cut a tree, plant, grass, or anything that has roots down and you water the area, you will see what you cut start to grow again. This is because the roots were not killed. The other problem with using bleach for an extended period is that if sprayed on wood and other building materials it actually starts to break down the products.
STOPPING MOLD AT THE ROOTS IS THE ONLY WAY!!!
Chlorine Bleach is NOT a registered EPA Mold Killing product!
If you think that we're just knocking bleach. Don't take our word for it! Go to http://epa.gov/mold/moldcourse/index.html and read what the EPA has to say about using bleach to kill mold. The EPA says that "The use of bleach is not recommended as a routine practice during mold clean-up" http://iaq.custhelp.com question #7.
Now you might ask: How do I kill mold if not with bleach?
Answer: Use an EPA approved and registered fungicide to kill the mold at its roots.
Interesting Facts About Mold Removal Taylor
The fear of hidden mold gives rise to visions of mold remediation experts traipsing around inside specialized enclosures while demolishing your home at tremendous expense to you. If you have noticed moldy odors or water damage, perhaps it is time to consult with a mold expert. However, for the large majority of homeowners who have not noticed the symptoms of mold growth, now is the perfect time to start looking.
Most are familiar with Stachybotrys, the "toxic black mold", which is common to water damaged gypsum wallboard. This mold organism requires high moisture availability, known as water activity, to develop. Optimal growth is achieved at .98 water activity, which is a lot of moisture. Big black patches, powerful odor, and lots of water, usually make this mold hard to miss. The real danger of hidden mold is the ability for a small mold problem to develop into a large and expensive one before being noticed. Wallpaper can help make that possible.
Wallpaper is more than a decorative wall covering. In fact, any large surfaced item or treatment added to a wall, such as bookshelves , paint or wallpaper, can alter the vapor and thermal performance of a wall. This knowledge is particularly important for the perimeter walls of the home, but should be a consideration for some interior walls, as well. There are other factors to consider, but in general; moisture moves from warm areas to cooler areas. So, in the summertime, warm moist air tries to make its way indoors where it is cooler and, in the case of a bathroom, warm moist air from bathing activities migrates to cooler areas. A well designed wall will slow the progression of moisture through the wall and yet allow it to pass through before trapping too much moisture and encountering psychrometric conditions that would permit condensation. Many wallpaper types impede moisture migration at the most crucial location, the coldest surface of the wall. The obstacle also makes possible a higher water activity in the underlying wallboard that leads to hidden mold growth.
Once you have discovered that you have hidden mold, it's time to determine to what extent the mold has developed. Determining the moisture source or psychrometric catalyst is paramount in estimating the size of the damaged area. You may find that the damage is small and limited to an area around a leaking window, air conditioning unit or associated with a vent blowing cold air directly on the area.
When cleaning the moldy area, it is best not to remove the wallpaper. Gypsum wallboard harboring mold growth is generally not considered salvable and removing the wallpaper will only serve to enable the trapped spores to become airborne. Depending on the size of the damaged area, it may be necessary to construct barriers around the work area to prevent the spread of mold spores to unaffected areas of the house while the damaged wall is being removed. Ideally, a timely home inspection will catch the common occurrence of hidden mold before it has grown to epic proportions.
How do I hire a Mold Removal Taylor Company?
Leaking Dryer Vents are a typical problem that we find all the time. This is one of the locations that are inspected in our Environmental Inspection process. It is very common to find high levels of lint behind the Washer/Dryer location. Sometimes we find mold growing in this location and other times we do not find mold. It is important to check this periodically because this can be a high humidity area.
There are several reasons why this problem occurs. We will list them now:
1. Improper installation on Day One of the Washer/Dryer Installation. What happens is the clamp on the vent pipe is not secured properly and when the Dryer is pushed back in, the vent pipe slips off. This is an installer error but not all installers are created equally. This can cause a serious moisture problem in this area. If not fixed immediately, the possibility of mold growth can happen.
In conclusion, it is important that you have this system inspected on a yearly basis to make sure you have not developed any leaks. It is also important to have this system cleaned every two years because of a possible Fire Hazard. This is also in addition to the possibility of Mold Growth in this area. As always, if you suspect any type of problem in Washer/Dryer Area, call a licensed Professional to check it out.
If you have any questions, feel free to call us or visit our website.
Which Mold Removal Taylor service provider is performs 24/7 water damage services?
If there is a toxic mold (fungus) problem, the first step after the source is identified is to eliminate it. This is done through a process known as remediation. If the problem is only a minor one, it's often easier and less costly for the homeowners to do it themselves. However, if it's a major problem, it's almost always recommended that the homeowner hire a professional for several reasons. Some are more necessary than others.
If there is a large amount of fungus present, special equipment is necessary to aid in the removal of the fungi and minimize the effects of toxic exposure. This may include, rubber gloves, respiratory masks, protective rubber suits or disposable paper overalls, eye goggles, polyethylene sheeting, fungi removal products, wet vacuums, HEPA vacuums, HEPA fans and in extreme cases a decontamination chamber or airlock.
And finally, you should keep in mind that when you are considering hiring a professional, inspectors of molds are not qualified to remove the fungus. An inspector's job is to inspect your home for mold and prevent their findings only, so make sure that the company you intend on hiring is qualified for mold remediation, otherwise you'll just be wasting everyone's time and your hard earned money.
For More Information on Mold Removal Taylor